253 lines
6.9 KiB
C++
253 lines
6.9 KiB
C++
#include "HC_LiquidCrystal_I2C.h"
|
|
#include <inttypes.h>
|
|
#include <Arduino.h>
|
|
#include <Wire.h>
|
|
|
|
// When the display powers up, it is configured as follows:
|
|
//
|
|
// 1. Display clear
|
|
// 2. Function set:
|
|
// DL = 1; 8-bit interface data
|
|
// N = 0; 1-line display
|
|
// F = 0; 5x8 dot character font
|
|
// 3. Display on/off control:
|
|
// D = 0; Display off
|
|
// C = 0; Cursor off
|
|
// B = 0; Blinking off
|
|
// 4. Entry mode set:
|
|
// I/D = 1; Increment by 1
|
|
// S = 0; No shift
|
|
//
|
|
// Note, however, that resetting the Arduino doesn't reset the LCD, so we
|
|
// can't assume that its in that state when a sketch starts (and the
|
|
// LiquidCrystal constructor is called).
|
|
|
|
HC_LiquidCrystal_I2C::HC_LiquidCrystal_I2C(uint8_t lcd_addr, uint8_t lcd_cols, uint8_t lcd_rows, uint8_t charsize)
|
|
{
|
|
_addr = lcd_addr;
|
|
_cols = lcd_cols;
|
|
_rows = lcd_rows;
|
|
_charsize = charsize;
|
|
_backlightval = LCD_BACKLIGHT;
|
|
}
|
|
|
|
void HC_LiquidCrystal_I2C::begin() {
|
|
Wire.begin();
|
|
_displayfunction = LCD_4BITMODE | LCD_1LINE | LCD_5x8DOTS;
|
|
|
|
if (_rows > 1) {
|
|
_displayfunction |= LCD_2LINE;
|
|
}
|
|
|
|
// for some 1 line displays you can select a 10 pixel high font
|
|
if ((_charsize != 0) && (_rows == 1)) {
|
|
_displayfunction |= LCD_5x10DOTS;
|
|
}
|
|
|
|
// SEE PAGE 45/46 FOR INITIALIZATION SPECIFICATION!
|
|
// according to datasheet, we need at least 40ms after power rises above 2.7V
|
|
// before sending commands. Arduino can turn on way befer 4.5V so we'll wait 50
|
|
delay(50);
|
|
|
|
// Now we pull both RS and R/W low to begin commands
|
|
expanderWrite(_backlightval); // reset expanderand turn backlight off (Bit 8 =1)
|
|
delay(1000);
|
|
|
|
//put the LCD into 4 bit mode
|
|
// this is according to the hitachi HD44780 datasheet
|
|
// figure 24, pg 46
|
|
|
|
// we start in 8bit mode, try to set 4 bit mode
|
|
write4bits(0x03 << 4);
|
|
delayMicroseconds(4500); // wait min 4.1ms
|
|
|
|
// second try
|
|
write4bits(0x03 << 4);
|
|
delayMicroseconds(4500); // wait min 4.1ms
|
|
|
|
// third go!
|
|
write4bits(0x03 << 4);
|
|
delayMicroseconds(150);
|
|
|
|
// finally, set to 4-bit interface
|
|
write4bits(0x02 << 4);
|
|
|
|
// set # lines, font size, etc.
|
|
command(LCD_FUNCTIONSET | _displayfunction);
|
|
|
|
// turn the display on with no cursor or blinking default
|
|
_displaycontrol = LCD_DISPLAYON | LCD_CURSOROFF | LCD_BLINKOFF;
|
|
display();
|
|
|
|
// clear it off
|
|
clear();
|
|
|
|
// Initialize to default text direction (for roman languages)
|
|
_displaymode = LCD_ENTRYLEFT | LCD_ENTRYSHIFTDECREMENT;
|
|
|
|
// set the entry mode
|
|
command(LCD_ENTRYMODESET | _displaymode);
|
|
|
|
home();
|
|
}
|
|
|
|
/********** high level commands, for the user! */
|
|
void HC_LiquidCrystal_I2C::clear(){
|
|
command(LCD_CLEARDISPLAY);// clear display, set cursor position to zero
|
|
delayMicroseconds(2000); // this command takes a long time!
|
|
}
|
|
|
|
void HC_LiquidCrystal_I2C::home(){
|
|
command(LCD_RETURNHOME); // set cursor position to zero
|
|
delayMicroseconds(2000); // this command takes a long time!
|
|
}
|
|
|
|
void HC_LiquidCrystal_I2C::setCursor(uint8_t col, uint8_t row){
|
|
int row_offsets[] = { 0x00, 0x40, 0x14, 0x54 };
|
|
if (row > _rows) {
|
|
row = _rows-1; // we count rows starting w/0
|
|
}
|
|
command(LCD_SETDDRAMADDR | (col + row_offsets[row]));
|
|
}
|
|
|
|
// Turn the display on/off (quickly)
|
|
void HC_LiquidCrystal_I2C::noDisplay() {
|
|
_displaycontrol &= ~LCD_DISPLAYON;
|
|
command(LCD_DISPLAYCONTROL | _displaycontrol);
|
|
}
|
|
void HC_LiquidCrystal_I2C::display() {
|
|
_displaycontrol |= LCD_DISPLAYON;
|
|
command(LCD_DISPLAYCONTROL | _displaycontrol);
|
|
}
|
|
|
|
// Turns the underline cursor on/off
|
|
void HC_LiquidCrystal_I2C::noCursor() {
|
|
_displaycontrol &= ~LCD_CURSORON;
|
|
command(LCD_DISPLAYCONTROL | _displaycontrol);
|
|
}
|
|
void HC_LiquidCrystal_I2C::cursor() {
|
|
_displaycontrol |= LCD_CURSORON;
|
|
command(LCD_DISPLAYCONTROL | _displaycontrol);
|
|
}
|
|
|
|
// Turn on and off the blinking cursor
|
|
void HC_LiquidCrystal_I2C::noBlink() {
|
|
_displaycontrol &= ~LCD_BLINKON;
|
|
command(LCD_DISPLAYCONTROL | _displaycontrol);
|
|
}
|
|
void HC_LiquidCrystal_I2C::blink() {
|
|
_displaycontrol |= LCD_BLINKON;
|
|
command(LCD_DISPLAYCONTROL | _displaycontrol);
|
|
}
|
|
|
|
// These commands scroll the display without changing the RAM
|
|
void HC_LiquidCrystal_I2C::scrollDisplayLeft(void) {
|
|
command(LCD_CURSORSHIFT | LCD_DISPLAYMOVE | LCD_MOVELEFT);
|
|
}
|
|
void HC_LiquidCrystal_I2C::scrollDisplayRight(void) {
|
|
command(LCD_CURSORSHIFT | LCD_DISPLAYMOVE | LCD_MOVERIGHT);
|
|
}
|
|
|
|
// This is for text that flows Left to Right
|
|
void HC_LiquidCrystal_I2C::leftToRight(void) {
|
|
_displaymode |= LCD_ENTRYLEFT;
|
|
command(LCD_ENTRYMODESET | _displaymode);
|
|
}
|
|
|
|
// This is for text that flows Right to Left
|
|
void HC_LiquidCrystal_I2C::rightToLeft(void) {
|
|
_displaymode &= ~LCD_ENTRYLEFT;
|
|
command(LCD_ENTRYMODESET | _displaymode);
|
|
}
|
|
|
|
// This will 'right justify' text from the cursor
|
|
void HC_LiquidCrystal_I2C::autoscroll(void) {
|
|
_displaymode |= LCD_ENTRYSHIFTINCREMENT;
|
|
command(LCD_ENTRYMODESET | _displaymode);
|
|
}
|
|
|
|
// This will 'left justify' text from the cursor
|
|
void HC_LiquidCrystal_I2C::noAutoscroll(void) {
|
|
_displaymode &= ~LCD_ENTRYSHIFTINCREMENT;
|
|
command(LCD_ENTRYMODESET | _displaymode);
|
|
}
|
|
|
|
// Allows us to fill the first 8 CGRAM locations
|
|
// with custom characters
|
|
void HC_LiquidCrystal_I2C::createChar(uint8_t location, uint8_t charmap[]) {
|
|
location &= 0x7; // we only have 8 locations 0-7
|
|
command(LCD_SETCGRAMADDR | (location << 3));
|
|
for (int i=0; i<8; i++) {
|
|
write(charmap[i]);
|
|
}
|
|
}
|
|
|
|
// Turn the (optional) backlight off/on
|
|
void HC_LiquidCrystal_I2C::noBacklight(void) {
|
|
_backlightval=LCD_NOBACKLIGHT;
|
|
expanderWrite(0);
|
|
}
|
|
|
|
void HC_LiquidCrystal_I2C::backlight(void) {
|
|
_backlightval=LCD_BACKLIGHT;
|
|
expanderWrite(0);
|
|
}
|
|
|
|
/*********** mid level commands, for sending data/cmds */
|
|
|
|
inline void HC_LiquidCrystal_I2C::command(uint8_t value) {
|
|
send(value, 0);
|
|
}
|
|
|
|
inline size_t HC_LiquidCrystal_I2C::write(uint8_t value) {
|
|
send(value, Rs);
|
|
return 1;
|
|
}
|
|
|
|
|
|
/************ low level data pushing commands **********/
|
|
|
|
// write either command or data
|
|
void HC_LiquidCrystal_I2C::send(uint8_t value, uint8_t mode) {
|
|
uint8_t highnib=value&0xf0;
|
|
uint8_t lownib=(value<<4)&0xf0;
|
|
write4bits((highnib)|mode);
|
|
write4bits((lownib)|mode);
|
|
}
|
|
|
|
void HC_LiquidCrystal_I2C::write4bits(uint8_t value) {
|
|
expanderWrite(value);
|
|
pulseEnable(value);
|
|
}
|
|
|
|
void HC_LiquidCrystal_I2C::expanderWrite(uint8_t _data){
|
|
Wire.beginTransmission(_addr);
|
|
Wire.write((int)(_data) | _backlightval);
|
|
Wire.endTransmission();
|
|
}
|
|
|
|
void HC_LiquidCrystal_I2C::pulseEnable(uint8_t _data){
|
|
expanderWrite(_data | En); // En high
|
|
delayMicroseconds(1); // enable pulse must be >450ns
|
|
|
|
expanderWrite(_data & ~En); // En low
|
|
delayMicroseconds(50); // commands need > 37us to settle
|
|
}
|
|
|
|
void HC_LiquidCrystal_I2C::load_custom_character(uint8_t char_num, uint8_t *rows){
|
|
createChar(char_num, rows);
|
|
}
|
|
|
|
void HC_LiquidCrystal_I2C::setBacklight(uint8_t new_val){
|
|
if (new_val) {
|
|
backlight(); // turn backlight on
|
|
} else {
|
|
noBacklight(); // turn backlight off
|
|
}
|
|
}
|
|
|
|
void HC_LiquidCrystal_I2C::printstr(const char c[]){
|
|
//This function is not identical to the function used for "real" I2C displays
|
|
//it's here so the user sketch doesn't have to be changed
|
|
print(c);
|
|
}
|