bme280/bme280.ino

@@ -1,152 +0,0 @@
-/***************************************************************************
-  This is a library for the BME280 humidity, temperature & pressure sensor
-
-  Designed specifically to work with the Adafruit BME280 Breakout
-  ----> http://www.adafruit.com/products/2650
-
-  These sensors use I2C or SPI to communicate, 2 or 4 pins are required
-  to interface. The device's I2C address is either 0x76 or 0x77.
-
-  Adafruit invests time and resources providing this open source code,
-  please support Adafruit andopen-source hardware by purchasing products
-  from Adafruit!
-
-  Written by Limor Fried & Kevin Townsend for Adafruit Industries.
-  BSD license, all text above must be included in any redistribution
-  See the LICENSE file for details.
- ***************************************************************************/
-
-/*
-Adapted by Starbeamrainbowlabs <https://starbeamrainbowlabs.com/>
-GitHub: @sbrl | Twitter: @SBRLabs | Reddit: u/Starbeamrainbowlabs
-
-# PROTOCOL SPEC
-## INPUT
-4 character commands. Whitespace and non-printable characters are ignored.
-
-### COMMANDS
-Command	| Meaning
---------|-----------------------------------------------------------
-read	| Read the sensor values and write the result to stdout
-
-*/
-
-#include <Wire.h>
-#include <SPI.h>
-// These libraries need installing in the Arduino IDE Library Manager (if you install the BME280 one it should prompt for the unified sensor library automatically)
-#include <Adafruit_Sensor.h>
-#include <Adafruit_BME280.h>
-
-#define BME_SCK 13
-#define BME_MISO 12
-#define BME_MOSI 11
-#define BME_CS 10
-
-
-#define SEALEVELPRESSURE_HPA (1013.25)
-
-Adafruit_BME280 bme; // I2C
-//Adafruit_BME280 bme(BME_CS); // hardware SPI
-//Adafruit_BME280 bme(BME_CS, BME_MOSI, BME_MISO, BME_SCK); // software SPI
-
-
-// Read buffer
-#define BUFFER_SIZE 4
-
-int bufferIndex = 0;
-char buffer[BUFFER_SIZE];
-
-void setup() {
-    Serial.begin(9600);
-    while(!Serial);    // time to get serial running
-    Serial.println(F("BME280 test"));
-
-    unsigned status;
-    
-    // default settings
-    status = bme.begin(0x76);  
-    // You can also pass in a Wire library object like &Wire2
-    // status = bme.begin(0x76, &Wire2)
-    if (!status) {
-        Serial.println("Could not find a valid BME280 sensor, check wiring, address, sensor ID!");
-        Serial.print("SensorID was: 0x"); Serial.println(bme.sensorID(),16);
-        Serial.print("        ID of 0xFF probably means a bad address, a BMP 180 or BMP 085\n");
-        Serial.print("   ID of 0x56-0x58 represents a BMP 280,\n");
-        Serial.print("        ID of 0x60 represents a BME 280.\n");
-        Serial.print("        ID of 0x61 represents a BME 680.\n");
-        while (1) delay(10);
-    }
-    
-    Serial.println("-- Default Test --");
-
-    Serial.println();
-}
-
-
-void loop() {
-    while(Serial.available() > 0) {
-        buffer[bufferIndex] = Serial.read();
-        
-        // Serial.print("Reading char, index: ");
-        // Serial.print(bufferIndex, DEC);
-        // Serial.print(", is greater: ");
-        // Serial.print(bufferIndex >= BUFFER_SIZE);
-        // Serial.print(", char: ");
-        // Serial.print(buffer[bufferIndex]);
-        // Serial.print(", hex: ");
-        // Serial.println(buffer[bufferIndex], HEX);
-        
-        // If it's a newline character, overwrite it
-        if(buffer[bufferIndex] < 48 || buffer[bufferIndex] > 122) {
-            // Serial.println("Skipping unrecognised char");
-            continue;
-        }
-        
-        if(bufferIndex >= BUFFER_SIZE - 1) {
-            // Serial.println("Handling command");
-            handle_command();
-            // Serial.print("Resetting index, is now: ");
-            bufferIndex = 0;
-            // Serial.println(bufferIndex, DEC);
-            continue;
-        }
-        
-        // Serial.println("Incrementing counter");
-        bufferIndex += 1;
-    }
-}
-
-void handle_command() {
-    // Serial.print("strcmp: ");
-    // Serial.println(strncmp(buffer, "read", BUFFER_SIZE), DEC);
-    
-    if(strncmp(buffer, "read", BUFFER_SIZE) == 0) { // 0 = They are the same
-        printValues();
-    }
-    else {
-        Serial.print("Error: Unknown command ");
-        Serial.println(buffer);
-    }
-}
-
-
-void printValues() {
-    Serial.print("Temperature ");
-    Serial.println(bme.readTemperature());
-    // Serial.println(" *C");
-
-    Serial.print("Pressure ");
-
-    Serial.println(bme.readPressure() / 100.0F);
-    // Serial.println(" hPa");
-
-    Serial.print("ApproxAltitude ");
-    Serial.println(bme.readAltitude(SEALEVELPRESSURE_HPA));
-    // Serial.println(" m");
-
-    Serial.print("Humidity ");
-    Serial.println(bme.readHumidity());
-    // Serial.println(" %");
-
-    // Serial.println();
-}