78 lines
2.5 KiB
C
78 lines
2.5 KiB
C
#pragma once
|
|
|
|
#include <lmic.h>
|
|
#include <hal/hal.h>
|
|
#include <SPI.h>
|
|
|
|
#include "settings.custom.h"
|
|
|
|
/*
|
|
* This is the main settings file - customise it to match your setup.
|
|
* Don't forget that you need to take a copy of settings.custom.cpp.example as
|
|
* settings.custom.cpp, and fill in the private keys the program needs to talk
|
|
* over LORaWAN.
|
|
*/
|
|
|
|
//////////////////////////////////
|
|
////////////// Main //////////////
|
|
//////////////////////////////////
|
|
|
|
// The speed at which we should talk over our main hardware serial connection.
|
|
#define BAUD_PC 115200
|
|
|
|
// Multiple devices can use the same SPI data pin AFAIKT, but some libraries
|
|
// *cough* SD *cough* are too stupid to figure out which pin it is on their own.
|
|
#define PIN_SPI_DATA 9
|
|
|
|
// The 'done' pin to pulse to signal to the TPL5111
|
|
#define PIN_TPL_DONE A0
|
|
|
|
// Uncomment to print RAM diagnostics at regular intervals.
|
|
//#define ENABLE_MEMORY_DIAGNOSTICS
|
|
|
|
/////////////
|
|
/// RFM95 ///
|
|
/////////////
|
|
|
|
// Whether to actually enable LMIC-based transmission or not.
|
|
#define ENABLE_RADIO
|
|
|
|
// The SPI chip-select pin for the RFM 95
|
|
#define PIN_SPI_CS_RFM95 10
|
|
|
|
// Pin mapping - see settings.custom.cpp
|
|
|
|
/////////////////////////////////
|
|
////////////// GPS //////////////
|
|
/////////////////////////////////
|
|
|
|
// The *TX* gin of the GPS device.
|
|
// This is swapped because we receive the GPS device's message on our side on
|
|
// the RX pin, and the GPS device transmits messages on the TX.
|
|
#define PIN_GPS_RX 5
|
|
// The *RX* pin on the GPS device.
|
|
// This is swapped because where the GPs device is receiving, we aresending and
|
|
// vice versa.
|
|
// The TX / RX here are according to *our* side, not the GPS device's side.
|
|
#define PIN_GPS_TX 4
|
|
// The speed at which we should talk to the GPS device. Some GPS devices
|
|
// require a certain speed in order to use certain commands, so it's important
|
|
// that you check the datasheets for the device you're using.
|
|
// 9600 is the correct speed for a NEO-6M.
|
|
#define BAUD_GPS 9600
|
|
|
|
//////////////////////////////////
|
|
////////// microSD Card //////////
|
|
//////////////////////////////////
|
|
|
|
// The chip select pin that activates the connection to the microSD card over SPI.
|
|
#define PIN_SPI_CS_SD 3
|
|
|
|
// The filename on the microSD card to store data in.
|
|
#define SD_FILENAME F("data.tsv")
|
|
|
|
// Whether to write debug information to the filename below. This could compromise privacy, so it should be commented out for production.
|
|
// #define SD_DEBUG_ENABLED
|
|
|
|
// The filename on the microSD card to store debug information in
|
|
#define SD_FILENAME_DEBUG F("debug.log")
|